Quick

Order

Log In / Register

My account

Cart (0)

You have 0 items in your shopping cart.

Custom Fabrication - Additional Services

Custom Fabrication - Additional Services

Beveling (45° standard bevel)

 Engraving PlasticAcrylicBrass & Aluminum
1 side Included in Price .20/plate .50/plate
2 sides .20/plate .40/plate NA
1 side with radius corners .25/plate NA NA


Pressure Sensitive Adhesive

Plastic - .02 per sq. in.
Acrylic - .02 per sq. in.
Brass & Aluminum - .03 per sq. in.

3 sq. in. minimum charge on all materials



Radius Corners

 Engraving PlasticAcrylicBrass & Aluminum
No Bevel .20/plate .25/plate .40/plate
With Bevel .25/plate NA NA



Drilled Holes

Standard Hole sizes are: 1/2", 1/4", 3/16", 5/32", 1/8", 3/32", 1/16"

 Engraving PlasticAcrylicBrassAluminum
1-2 holes per plate (same diameter) .16/plate .16/plate .20/plate .24/plate
3-4 holes per plate (same diameter) .20/plate .20/plate .24/plate .28/plate

Countersinking: add 5¢ per hole

Other available hole sizes: All 1/64" increments up to 1/2"

Larger hole sizes, precision placement of holes in control panels or switch plates quoted upon request

Required Hole Placement Information

  • Measurement in inches from the center of one hole to the center of the other hole. (line a)
  • Measurement in inches from the center of the hole to the top of the material. (line b)
  • Measurement in inches from the center of the hole to the edge of the material. (line c)


Bending (up to 12" length)

 Engraving PlasticAcrylicBrass & Aluminum
1st Bend .75 ea $1.50 ea* NA
Additional Bends .35 ea .75 ea* NA

*May be subject to additional packaging charges.



Polished Edges

 Engraving PlasticAcrylicBrass & Aluminum
Jointed Finished edges .10/perimeter in. .10/perimeter in. .10/perimeter in.
Jointed Flame polished NA .20/perimeter in. NA
Jointed Buffed edges .30/perimeter in. .30/perimeter in. NA


Pinning (Applies to plastic material only)

Solvent welded safety pin F20 - .35 ea

Solvent welded bull dog clip, swivel bulldog clip - .40 ea

Solvent welded safety pin J20, double post bar w/clutch, clear plastic pocket clip J18 - .45 ea

Heat fused safety pin (3/32" material only) - .50 ea

Heat fused double post bar with clutch (3/32" material only) - .60 ea


Other findings are available. Contact a customer service representative for a quote



Special Shapes

Johnson Plastics has the capabilities to provide non-standard shapes in a variety of sizes. Prices for irregular shapes can normally be figured by taking the square inch charge per piece of material as shown above and adding an additional 25¢ per piece. For parts that are not beveled, add 35¢ per piece. Note: Unisub FRP is excluded from this surcharge.

Johnson Plastics has a large selection of irregular shapes in its files. If the shape you are looking for is not currently in our system, a one TIME $40.00 SET-UP (DIGITIZING) CHARGE WILL BE ADDED TO THE INITIAL ORDER.



State Shapes

Badges in the shape of states are also available. Pricing for state-shaped badges can also be figured by taking the square inch charge per piece of material as shown above and adding an additional 25¢ per piece. For state shapes that are not beveled, add 35¢ per piece. There is no set-up charge for state shapes.



Minimum Fabrication Order : $5.00 per line item

Custom fabricated pieces can only be ordered through customer service 800-869-7800

THESE PRODUCTS CAN ONLY BE ORDERED THROUGH CUSTOMER SERVICE 800-869-7800

8